Agilent Technologies AIC 5000 Скачать руководство пользователя | Manualshive

Страница: 23 / 64

background image

AIC 5000 Installation and Configuration

17

Configure the SS420x

If you will be using an SS420x attached to the AIC (used for analog
acquisition), it will need to be configured locally. If you are not using a
local SS420x, you may skip this section.

1.

Start the data system software by clicking

Start > All Programs

> Chromatography > EZChrom Elite

.

Go to Tools, Interface

Configuration and select the SS420x.

2.

From the SS420x configuration dialog, select the Serial port to
which the SS420x is connected and then select the

Installed

check box to enable the configuration of the interface. Then
proceed to select the appropriate settings for the interface.

Baud Rate

The communication baud rate is displayed here. To change
the baud rate, click

Advanced.

SS420x Advanced Port Configuration

The Advanced – SS420x Port Configuration dialog box
enables you to set the baud rate for the SS420x interface.
Click

Auto Detect

to determine the current baud rate

setting. Click

OK

to exit.

Base Frequency

Select the base frequency. The default setting for the
SS420x is 10 Hz, which gives optimal signal to noise, and
can be used in countries using either 50Hz or 60Hz. The
base frequencies available will depend on the baud rate
chosen. If the baud rate is less than 38400bps, the base
frequencies 100 and 120 will not be available. If you choose
a higher base frequency, you must select a base frequency
which can be evenly divided into your line frequency (i.e.
30 for 60Hz countries and 25 for 50Hz countries). If
selected incorrectly, you may see line frequency noise on
your chromatogram. For best performance, select a base
frequency close to the maximum sampling frequency you
will be using to acquire data.

«
...
21
22
23
24
25
...
»

Содержание AIC 5000

































































Отзывы:

Нет отзывов

Похожие инструкции для AIC 5000

Relion 670 series

Бренд: ABB Страницы: 760

Бренд: ABB Страницы: 128

Бренд: S&C Страницы: 40

Бренд: Danfoss Страницы: 32

PVG 16 PVH/Covers

Бренд: Danfoss Страницы: 112

Бренд: Danfoss Страницы: 44

PVG 16 PVH/Covers

Бренд: Danfoss Страницы: 144

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 64

Бренд: Danfoss Страницы: 8

VLT AutomationDrive FC 360

Бренд: Danfoss Страницы: 60

Бренд: Danfoss Страницы: 6

Бренд: Danfoss Страницы: 4

Бренд: Danfoss Страницы: 8

Бренд: Danfoss Страницы: 2

ECL Comfort 110

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 24

Бренд: Salda Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды