Agilent Technologies agilent 7683B Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 202

Agilent Technologies agilent 7683B Скачать руководство пользователя страница 66

66

Installation, Operation, and Maintenance

Part 1, Installation

2

Installation

Procedure 12. Updating the Firmware

The 7683B ALS sampler requires the firmware revisions noted in

Before using the new sampler, check the firmware revisions as described
below.

All GC and ALS systems

The Agilent Firmware Update Utility, revision 4.0 or higher, will display the
firmware revision of any connected device, whether GC or ALS. It is a
general-purpose utility that can update the firmware on any Agilent GC or
sampling device whose firmware can be flash-programmed.

To obtain the utility:

•

All users can download the latest version of this utility from the Agilent
Web site at www.agilent.com/chem. Search the site for “firmware”.

Table 10

Minimum firmware revisions for 7683B use

Instrument

Minimum firmware version required

6890A GC

A.03.08 (chip set)

6890 Plus GC

A.03.08 (chip set)

6890N GC

A.05.04

6850 GC with serial number< US00003200

A.03.03

6850 GC with serial number > US10243001
(includes 6850 Network and Series II)

A.05.03

6850 GC handheld controller (G2629A)

A.05.02

G2913A injector

A.11.00

G2613A Injector

A.10.07

G2614A Tray

A.02.00

G2612A ALS controller card for 6890 Plus

A.02.00

G2912A controller

A.02.00

«
...
64
65
66
67
68
...
»

Содержание agilent 7683B











































































































































































































Отзывы:

Нет отзывов