Agilent Technologies 5977B Series Скачать руководство пользователя страница 81

Страница: 81 / 258

CI Troubleshooting

Large peak at

m/z

If the abundance of the peak at

m/z

19 is more than half abundance of the

peak at

m/z

17, there probably is too much water in the system.

The system was not baked out sufficiently after it was last vented.

Bake out the system as described in the

Maintenance

chapter of this manual.

Moisture left over in the reagent gas supply tubing and flow module

Purge the reagent gas supply lines for at least 60 minutes.

Contaminated reagent gas supply

Replace the reagent gas supply, and purge the lines and flow module.

Saturated methane/isobutane gas purifier

Replace the gas purifier.

Содержание 5977B Series



































































































































































































































































Результаты поиска

Содержание 5977B Series

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies 5977B Series, Руководство по устранению неисправностей и техническому обслуживанию

Результаты поиска

Содержание 5977B Series

Отзывы:

Бренды по названию

Популярные бренды