Agilent Technologies 5977B Series Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 258

Agilent Technologies 5977B Series Скачать руководство пользователя страница 65

CI Troubleshooting

3

65

Troubleshooting Tips and Tricks

Rule 1: Look for what has been changed.

Many problems are introduced accidentally by human actions. Every time any
system is disturbed, there is a chance of introducing a new problem.

•

If the MSD was just pumped down after maintenance, suspect air leaks or
incorrect assembly.

•

If the reagent gas bottle or gas purifier were just changed, suspect leaks or
contaminated or incorrect gas.

•

If the GC column was just replaced, suspect air leaks or contaminated or
bleeding column.

•

If you have just switched ion polarity or reagent gas, suspect the tune file
you have loaded in memory. Is it the appropriate file for your mode of
operation?

Rule 2: If complex is not working, go back to simple.

A complex task is not only more difficult to perform, but also more difficult to
troubleshoot as well. For example, CI requires more parts to work correctly
than EI does.

•

If you are having trouble with NCI, verify that PCI still works.

•

If you are having trouble with other reagent gases, verify that methane still
works.

•

If you are having trouble with CI, verify that EI still works.

Rule 3: Divide and conquer.

This technique is known as half-split troubleshooting. If you can isolate the
problem to only part of the system, it is much easier to locate.

•

To isolate an air leak, select

Shutoff valve

. If the abundance of

m/z

32

decreases, the problem is not in the flow module.

«
...
63
64
65
66
67
...
»

Содержание 5977B Series



































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды