manualshive.com logo in svg

Agilent Technologies 5977B Series, Руководство по устранению неисправностей и техническому обслуживанию

Поделиться
Скачать
Agilent Technologies 5977B Series Скачать руководство пользователя страница 176

176

5977B Series MSD Troubleshooting and Maintenance Manual

6

Vacuum System

Calibration Valves and Vent Valve

Calibration valves

A calibration valve (See 

Figure 36

 on page 177) is an electromechanical valve 

with a vial to hold the tuning compound. When a calibration valve is opened, 
tuning compound in the vial diffuses into the ion source. EI MSDs have one 
calibration valve; CI MSDs have a second calibration valve for the CI tuning 
compound. The valves are controlled by the MSD Data Acquisition.

EI calibration valve

The EI calibration valve is held onto the top of the analyzer chamber by 
two screws. A small O-ring provides a face seal.

The diffusion pump has a calibration valve with less restriction than that in 
the turbo MSD; this allows the correct diffusion of calibrant for each vacuum 
system.

Perfluorotributylamine (PFTBA) is the most commonly used tuning 
compound for EI operation. PFTBA is required for automatic tuning of the 
MSD. Other compounds can be used for manual tuning.

CI calibration valve

The CI tuning compound is

 

perfluoro-5,8-dimethyl-3,6,9-trioxidodecane 

(PFDTD). 

The CI calibration valve is part of the reagent gas flow control 

module. It is controlled by the Data Acquisition software. It opens 
automatically during CI autotune or manual tuning, allowing PFDTD to diffuse 
through the GC/MSD interface and into the ion source.

Vent valve

The vent valve knob (See 

Figure 37

 on page 178) screws into a threaded port 

in the front of the calibration valve. An O-ring is compressed between the knob 
and the valve to form a seal. The threaded end of the knob has an air passage 
inside it, allowing air to flow into the manifold when the knob is partially 
unscrewed. If you turn the knob too far, the O-ring can come out of its slot.

Содержание 5977B Series



































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды