Agilent Technologies 5977B Series Скачать руководство пользователя страница 139 | Manualshive

Страница: 139 / 258

Agilent Technologies 5977B Series Скачать руководство пользователя страница 139

General Maintenance

4

5977B Series MSD Troubleshooting and Maintenance Manual

139

To Lubricate the Vent Valve O-Ring

Materials needed

•

Cloths, clean (05980-60051)

•

Gloves, clean, lint-free

•

Large (8650-0030)

•

Small (8650-0029)

•

Grease, Apiezon L, high vacuum (6040-0289)

•

O-ring, vent valve (0905-1217). Replace if the old O-ring is worn or damaged

The vent valve O-ring needs a thin coat of lubrication to ensure a good vacuum
seal and smooth operation. If the vent valve O-ring does not turn smoothly or
does not seal correctly, lubricate it using this procedure.

Procedure

1

Vent the MSD.

2

Completely remove the vent valve knob. (See

3

Inspect the O-ring. If the O-ring appears damaged, replace it.

4

Use a clean, lint-free cloth or glove to spread a

thin

coat of high vacuum

grease on the exposed surface of the O-ring.

5

Use a clean, lint-free cloth or glove to wipe away excess grease. If the
O-ring looks shiny, there is too much grease on it

C A U T I O N

Vacuum seals other than the side plate O-ring and vent valve O-ring do not need to be
lubricated. Lubricating other seals can interfere with their function.

C A U T I O N

Excess grease can trap air and dirt. Grease on surfaces of the O-ring other than the
exposed surface can trap air, resulting in air spikes during operation.

«
...
137
138
139
140
141
...
»

Содержание 5977B Series



































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды