Agilent Technologies 5977B Series Скачать руководство пользователя страница 132

Страница: 132 / 258

132

5977B Series MSD Troubleshooting and Maintenance Manual

General Maintenance

To Install the EI Calibration and Vent Valve Assembly

Materials needed

•

Calibration valve

•

Diffusion (G7077-60211)

•

Turbo (G7077-60204)

•

O-ring for calibration valve (0905-1217)

•

PFTBA (05971-60571) or other tuning compound

•

Screwdriver, Torx T-20 (8710-1615)

Procedure

Remove the old valve assembly. (See

“To Remove the EI Calibration and

Ensure the valve O-ring is in place. If it is worn or damaged, replace it.

Install the calibration and vent valve assembly, and tighten the screws that
hold it in place.

Reconnect the calibration valve cable to the connector next to the fan.

Remove the vial from the new calibration valve. (See

“To Refill the EI

Calibration Vial”

on page 128.) The valve is supplied with a vial already

installed.

Fill and reinstall the calibration vial.

Pump down the MSD.





C A U T I O N

Failure to purge the calibration valve will damage the filaments and detector.

Содержание 5977B Series



































































































































































































































































Результаты поиска

Содержание 5977B Series

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies 5977B Series, Руководство по устранению неисправностей и техническому обслуживанию

Результаты поиска

Содержание 5977B Series

Отзывы:

Бренды по названию

Популярные бренды