Agilent Technologies 5977B CI MSD Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 254

background image

2

Installing 8890 GC Columns



To Condition a Capillary Column

5977B Series MSD Operating Manual

41

To Condition a Capillary Column

Materials needed

•

Carrier gas, (99.9995% pure or better)

•

Wrench, open-end, 1/4-inch and 5/16-inch (8710-0510)

Procedure

1

Install the column in the GC inlet. (See

“To Install a Capillary Column in a

Split/Splitless Inlet”

2

Set a minimum velocity of 30 cm/s, or as recommended by the column
manufacturer. Allow the carrier gas to flow through the column at room
temperature for 15 to 30 minutes to remove air.

3

Program the oven from room temperature to the maximum temperature
limit for the column.

4

Increase the temperature at a rate of 10 to 15 °C/min.

5

Hold at the maximum temperature for 30 minutes.

6

Set the GC oven temperature to 30 °C, and wait for the GC to become ready.

7

Attach the column to the GC/MSD interface. (See

“To Install a Capillary

Column in the GC/MSD Interface Using the Self-Tightening Column Nut”

WARNING

Do not condition your capillary column with hydrogen. Hydrogen accumulation
in the GC oven can result in an explosion. If you plan to use hydrogen as your
carrier gas, first condition the column with ultrapure (99.999% or better) inert
gas such as helium, nitrogen, or argon.

WARNING

The GC operates under high temperatures. Do not touch any GC parts unless
you are certain they are cool.

CAUTION

Never exceed the maximum column temperature, either in the GC/MSD
interface, the GC oven, or the inlet.

«
...
39
40
41
42
43
...
»

Содержание 5977B CI MSD































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 5977B CI MSD

Бренд: SAER Elettropompe Страницы: 16

Бренд: Valeo Страницы: 88

Бренд: Valdemar Energy Страницы: 61

Бренд: EBARA Страницы: 22

Бренд: VARISCO Страницы: 72

Бренд: Daikin Страницы: 30

Бренд: Pentair Pool Products Страницы: 2

Бренд: AMT Страницы: 8

Бренд: Rietschle Страницы: 17

Бренд: Samoa Страницы: 38

Бренд: Serenity Страницы: 3

Бренд: Daewoo Страницы: 16

Бренд: Laars Страницы: 36

Бренд: Blue Angel Страницы: 4

Бренд: DEMA Страницы: 8

Бренд: Warren rupp Страницы: 16

Бренд: Aquacal Страницы: 108

Бренд: Lafferty Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды