Agilent Technologies 5977B CI MSD Скачать руководство пользователя страница 215

Страница: 215 / 254

General Maintenance



To Replace a Filament in an EI XTR, SS, or Inert Source

5977B Series MSD Operating Manual

215

To Replace a Filament in an EI XTR, SS, or
Inert Source

Materials needed

•

Filament assembly (G7005-60061)

•

Gloves, clean, lint-free

•

Large (8650-0030)

•

Small (8650-0029)

•

Hex ball driver, 1.5-mm (8710-1570)

Procedure

Vent the MSD. (See

“Venting the MSD”

on page 116.)

Open the analyzer chamber. (See

“To Open the Analyzer Chamber”

page 176.)

Remove the ion source. (See

“To Remove the EI XTR, SS, or Inert Source”

page 196.)

Remove the gold plated screw and washer from the filament. (See

Figure 69

on page 216.)

Slide the filament assembly off the ion source assembly.



WARNING

The analyzer operates at high temperatures. Do not touch any part until you
are sure it is cool.



Содержание 5977B CI MSD































































































































































































































































Результаты поиска

Содержание 5977B CI MSD

Отзывы:

Похожие инструкции для 5977B CI MSD

Бренды по названию

Популярные бренды

Agilent Technologies 5977B CI MSD, Руководство по эксплуатации

Результаты поиска

Содержание 5977B CI MSD

Отзывы:

Похожие инструкции для 5977B CI MSD

Бренды по названию

Популярные бренды