Agilent Technologies 5975T LTM GC/MSD Скачать руководство пользователя страница 97

Страница: 97 / 270

Instrument Power On and Communication Symptoms

Troubleshooting and Maintenance Guide

PC Cannot Communicate with Instrument

•

Run a

ping

test

The MS-DOS

ping

command verifies communications across

a TCP/IP connection. To use it, open the command prompt
window. Type

ping

followed by an IP address. For example, if

the IP address is 10.1.1.101, enter

ping 10.1.1.101

. If LAN

communications are working properly, you will see a
successful reply. For example:

If the ping test is successful, check the software configuration.

If the ping test is unsuccessful, do the following:

•

Check the LAN cabling.

•

Verify the IP address, subnet mask, and gateway addresses.

•

Check that a crossover cable for single instrument to
computer direct connection is installed.

Содержание 5975T LTM GC/MSD















































































































































































































































































Результаты поиска

Содержание 5975T LTM GC/MSD

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies 5975T LTM GC/MSD, Руководство по устранению неисправностей и техническому обслуживанию

Результаты поиска

Содержание 5975T LTM GC/MSD

Отзывы:

Бренды по названию

Популярные бренды