Agilent Technologies 5975T LTM GC/MSD Скачать руководство пользователя страница 80

Страница: 80 / 270

Troubleshooting and Maintenance Guide

Not Ready Symptoms

The Inlet Pressure or Flow Fluctuates

A fluctuation in inlet pressure causes variations in the flow rate
and retention times during a run. Do the following:

•

Check if the gas purifier or gas generator is operating at or
near capacity.

•

Check the supply gas for sufficient delivery pressure.

•

Verify that the supply pressure regulator is functioning
properly.

•

Check for leaks. (See

Chapter 8

, “Checking for Leaks”.)

•

Check for large restrictions in the inlet liner or split vent
trap.

•

Verify that the correct liner is installed.

•

Check for a restriction in headspace, purge and trap, and
any other external sampling devices.

Содержание 5975T LTM GC/MSD















































































































































































































































































Результаты поиска

Содержание 5975T LTM GC/MSD

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies 5975T LTM GC/MSD, Руководство по устранению неисправностей и техническому обслуживанию

Результаты поиска

Содержание 5975T LTM GC/MSD

Отзывы:

Бренды по названию

Популярные бренды