manualshive.com logo in svg

Agilent Technologies 5975T LTM GC/MSD, Руководство по устранению неисправностей и техническому обслуживанию

Поделиться
Скачать
Agilent Technologies 5975T LTM GC/MSD Скачать руководство пользователя страница 69

Chromatographic Symptoms

3

Troubleshooting and Maintenance Guide

69

Air Leaks

Air leaks are a problem for any instrument that requires a 
vacuum to operate. Leaks are generally caused by vacuum seals 
that are damaged or not fastened correctly. Symptoms of leaks 
include:

•

Higher than normal analyzer chamber pressure or foreline 
pressure

•

Higher than normal background

•

Peaks characteristic of air (

m/z

 18, 28, 32, and 44 or 

m/z

 14 

and 16)

•

Poor sensitivity

•

Low relative abundance of 

m/z

 502 (this varies with the tune 

program used)

Leaks can occur in either the GC or the MSD. The most likely 
point for an air leak is a seal you recently opened.

In the GC, most leaks occur in:

•

GC inlet septum

•

GC inlet column nut

•

Broken or cracked capillary column

Leaks can occur in many more places in the MSD:

•

GC/MSD interface column nut

•

Side plate O-ring (all the way around)

•

Vent valve O-ring

•

Calibration valve

•

GC/MSD interface O-ring (where the interface attaches to 
the analyzer chamber)

•

Front and rear end plate O-rings

•

Turbo pump O-ring

Содержание 5975T LTM GC/MSD















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды