manualshive.com logo in svg

Agilent Technologies 5975T LTM GC/MSD, Руководство по устранению неисправностей и техническому обслуживанию

Поделиться
Скачать
Agilent Technologies 5975T LTM GC/MSD Скачать руководство пользователя страница 67

Chromatographic Symptoms

3

Troubleshooting and Maintenance Guide

67

•

Source temperature sensor is shorted

•

Mass filter (quad) temperature sensor is open

•

Mass filter (quad) temperature sensor is shorted

•

No heater voltage (heater fuse has probably failed)

•

Heater voltage is too low

•

Temperature zone has timed out (heater failed, bad heater 
wiring, or loose temperature sensor)

•

Problem with the temperature control electronics

•

Source heater is open

•

Source heater is shorted

•

Mass filter heater is open

•

Mass filter heater is shorted

The high vacuum pump is not ready

•

Turbo pump is on but has not had enough time (5 minutes) 
to reach 80% of its normal operating speed

•

Turbo pump is not working correctly

•

MSD electronics are not working correctly

The system is in standby

This message is triggered by a shutdown signal on the remote 
start cable. It is usually caused by a GC fault, an ALS fault, or a 
bad cable connection. Once the cause of the fault is corrected, 
selecting 

MS ON

 or checking MSD status should remove the 

message.

The system is in vent state

The message says the system is vented, but if the fault has just 
occurred it may still be under vacuum and the turbo pump may 
still be at high speed. Wait at least 30 minutes after seeing this 
message before you actually vent the MSD.

•

System was vented on purpose (no problem)

C A U T I O N

Venting the MSD too soon after this message appears can damage 
a turbo pump.

Содержание 5975T LTM GC/MSD















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды