Agilent Technologies 5975T LTM GC/MSD Скачать руководство пользователя страница 66

Страница: 66 / 270

Troubleshooting and Maintenance Guide

Chromatographic Symptoms

Lens supply fault

•

Electrical short in the analyzer

•

MSD electronics are not working correctly

Log amplifier ADC error

•

MSD electronics are not working correctly

No peaks found

•

Emission current was set to 0

•

Electron multiplier voltage is too low

•

Amu gain or offset is too high

•

Poor mass axis calibration

•

Amu gain or offset is too high

•

Calibration vial(s) empty or almost empty

•

Excessive pressure in the analyzer chamber

•

Air leak

•

Electron multiplier voltage is too low

•

Signal cable is not connected

•

Electrical leads to the detector are not connected correctly

•

HED power supply output cable failed

•

Electrical leads to the ion source are not connected
correctly

•

Filament shorted to the source body

Temperature control disabled

•

One of the heater fuses has failed

•

MSD electronics are not working correctly

Temperature control fault

This indicates that something has gone wrong with the
temperature control of either the ion source or mass filter
(quad) heater. The cause can be further isolated by selecting

Status/MS Temp Ctlr Status

in the

Tune and Vacuum Control

view.

One of the following should be displayed as the cause:

•

Source temperature sensor is open

Содержание 5975T LTM GC/MSD















































































































































































































































































Результаты поиска

Содержание 5975T LTM GC/MSD

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies 5975T LTM GC/MSD, Руководство по устранению неисправностей и техническому обслуживанию

Результаты поиска

Содержание 5975T LTM GC/MSD

Отзывы:

Бренды по названию

Популярные бренды