manualshive.com logo in svg

Agilent Technologies 5975T LTM GC/MSD, Руководство по устранению неисправностей и техническому обслуживанию

Поделиться
Скачать
Agilent Technologies 5975T LTM GC/MSD Скачать руководство пользователя страница 64

64

Troubleshooting and Maintenance Guide

3

Chromatographic Symptoms

Analyzer Error Messages

Sometimes, a problem in your MSD will cause an error message 
to appear in the MSD ChemStation software. Some error 
messages appear only during tuning. Other messages may 
appear during tuning or data acquisition.

Some error messages are “latched.” These messages remain 
active in your data system even if the condition that caused the 
message has corrected itself. If the cause is removed, these 
messages can be removed by checking instrument status 
through the data system.

Difficulty in mass filter electronics

•

Pressure in the analyzer chamber is too high

•

RFPA is not adjusted correctly

•

Mass filter (quad) contacts are shorted or otherwise not 
working correctly

•

Mass filter is not working correctly

•

MSD electronics are not working correctly

Difficulty with the electron multiplier supply

•

Large peak, such as the solvent peak, eluted while the 
analyzer was on

•

Pressure in the analyzer chamber is too high

•

MSD electronics are not working correctly

Difficulty with the fan

If a cooling fan fault occurs, the vacuum control electronics 
automatically shut off the high vacuum pump and the ion 
source and mass filter heaters. Therefore, the message: 

The 

system is in vent state

 may also appear. It is important to note 

that even though the high vacuum pump is off, the analyzer 
chamber may not actually be vented. See 

The system is in vent 

state

 in this section for precautions to take.

•

One of the fans is disconnected

•

One of the fans has failed

•

MSD electronics are not working correctly

Содержание 5975T LTM GC/MSD















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды