Agilent Technologies 5975T LTM GC/MSD Скачать руководство пользователя страница 61

Страница: 61 / 270

Chromatographic Symptoms

Troubleshooting and Maintenance Guide

Temperature Symptoms

The instrument has the following heated zones:

•

Ion source (

Source

in the MSD ChemStation software)

•

Mass filter (

Quad

in the MSD ChemStation software)

•

GC/MSD interface

Thermal Aux #2

in the MSD ChemStation

software

•

LTM column module

•

Heated guard column enclosure

•

Inlet

Each heated zone has a heater and temperature sensor.

Ion source will not heat up

•

High vacuum pump is off or has not reached normal
operating conditions*

•

Incorrect temperature setpoint

•

Ion source has not had enough time to reach temperature
setpoint

•

Ion source heater cartridge is not connected*

•

Ion source temperature sensor is not connected*

•

Ion source heater failed (burned out or shorted to ground)*

•

Ion source temperature sensor failed*

•

Source power cable is not connected to the side board*

•

MSD electronics are not working correctly

* These will cause an error message.

Mass filter (quad) heater will not heat up

•

High vacuum pump is off or has not reached normal
operating conditions*

•

Incorrect temperature setpoint

•

Mass filter has not had enough time to reach temperature
setpoint

•

Mass filter heater cartridge is not connected*

•

Mass filter temperature sensor is not connected*

•

Mass filter heater failed (burned out or shorted to ground)*

•

Mass filter temperature sensor failed*

Содержание 5975T LTM GC/MSD















































































































































































































































































Результаты поиска

Содержание 5975T LTM GC/MSD

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies 5975T LTM GC/MSD, Руководство по устранению неисправностей и техническому обслуживанию

Результаты поиска

Содержание 5975T LTM GC/MSD

Отзывы:

Бренды по названию

Популярные бренды