manualshive.com logo in svg

Agilent Technologies 5975T LTM GC/MSD, Руководство по устранению неисправностей и техническому обслуживанию

Поделиться
Скачать
Agilent Technologies 5975T LTM GC/MSD Скачать руководство пользователя страница 57

Chromatographic Symptoms

3

Troubleshooting and Maintenance Guide

57

relative abundance of 

m/z

 502 for a fixed set of operating 

parameters, there may be a problem. The charts in the MSD 
ChemStation software are useful for identifying changes. Select 

View Tunes

 from the 

Checkout

 menu in the 

Instrument Control

 view.

Low 

relative

 abundance of 

m/z

 502 should not be confused with 

low 

absolute

 abundances at high masses. Sensitivity at high 

masses can be excellent even if the relative abundance of 

m/z

 502 is near 3%. If your MSD produces low absolute 

abundances at high masses, refer to the symptom 

High mass 

sensitivity is poor

.

Tune programs other than autotune have different relative 
abundance targets. The DFTPP and BFB target tune programs 
tune the MSD to achieve about a 0.8% ratio of 

m/z

 502/69.

•

Tune program/tune file has a different relative abundance 
target 

(3% only applies to Autotune)

•

Not enough time for the MSD to warm up and pump down

•

Analyzer chamber pressure is too high

•

Ion source temperature is too high

•

Column (carrier gas) flow is too high

•

Poor filament operation

•

Dirty ion source

•

Air leak

•

Incorrect DC polarity on the quadrupole mass filter

Spectra look different from those acquired with other MSDs

Ion ratios are different from those in older models MSDs. This is 
due to the HED detector, and is normal. To get spectra similar to 
older MSDs, use 

Standard Spectra Tune

, available in the 

Manual 

Tune

 view. Note that this tune takes much longer to complete 

than 

Autotune.

High mass sensitivity is poor

This refers to a condition where the 

absolute

 abundance at the 

upper end of the mass range is poor. Absolute abundance 
should not be confused with the 

relative

 abundance 

(percentage) of 

m/z

 502 to 

m/z

 69. Sensitivity at high masses 

can be excellent even if the relative abundance of 

m/z

 502 is low.

•

Wrong tune program

•

Wrong tune file

Содержание 5975T LTM GC/MSD















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды