manualshive.com logo in svg

Agilent Technologies 5975T LTM GC/MSD, Руководство по устранению неисправностей и техническому обслуживанию

Поделиться
Скачать
Agilent Technologies 5975T LTM GC/MSD Скачать руководство пользователя страница 39

Chromatographic Symptoms

3

Troubleshooting and Maintenance Guide

39

Peaks Not Displayed/No Peaks

•

If using an autosampler:

•

Ensure that there is sample in the vial.

•

Verify that the ALS plunger carriage is secured to the 
syringe plunger.

•

Check that the syringe is installed correctly and draws 
sample.

•

Verify that the turret is loaded correctly and injections 
are not from out-of-sequence vials.

•

Watch to see that the sample is pulled into the syringe.

•

Check the column for proper installation. 

•

Ensure that the column is not plugged. Perform column 
maintenance. 

•

Check for leaks. (See 

“Checking for Leaks” 

on page 99.)

No peaks

If an analysis shows no chromatographic peaks, only a flat 
baseline or minor noise, run one of the automated tune 
programs. If the MSD passes tune, the problem is most likely 
related to the GC. If the MSD does not pass tune, the problem is 
most likely in the MSD.

Passes tune

•

Incorrect sample concentration

•

No analytes present

•

Syringe missing from the ALS or not installed correctly

•

Injection accidentally made in split mode instead of splitless 
mode

•

Empty or almost empty sample vial

•

Dirty GC inlet

•

Leaking GC inlet*

•

Loose column nut at the GC inlet*

* These could cause a fault condition in the GC that would prevent 

the GC from operating.

Does not pass tune

•

Calibration vial is empty

Содержание 5975T LTM GC/MSD















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды