Agilent Technologies 5975T LTM GC/MSD Скачать руководство пользователя страница 36

Страница: 36 / 270

Troubleshooting and Maintenance Guide

Chromatographic Symptoms

Peak Areas Not Repeatable

Check the ALS syringe operation. (See the Troubleshooting
section of the

7683 Automatic Liquid Sampler Installation,

Operation and Maintenance

manual.)

•

Replace the syringe.

•

Check for leaks in the inlet, liner (as applicable), and
column connection. (See

“Checking for Leaks”

on page 99.)

•

Check sample level in vials.

•

Run replicates of known standards to verify the problem.

•

Consider if this is the first run. (Has the instrument
stabilized?)

Poor repeatability

•

Dirty syringe needle

•

Dirty GC inlet

•

Leaking GC inlet*

•

Injection is too large

•

Loose column connections

•

Variations in pressure, column flow, and temperature

•

Dirty ion source

•

Loose connections in the analyzer

•

Ground loops

* This could cause a fault condition in the GC that would prevent

the GC from operating.

Содержание 5975T LTM GC/MSD















































































































































































































































































Результаты поиска

Содержание 5975T LTM GC/MSD

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies 5975T LTM GC/MSD, Руководство по устранению неисправностей и техническому обслуживанию

Результаты поиска

Содержание 5975T LTM GC/MSD

Отзывы:

Бренды по названию

Популярные бренды