manualshive.com logo in svg

Agilent Technologies 5975T LTM GC/MSD, Руководство по устранению неисправностей и техническому обслуживанию

Поделиться
Скачать
Agilent Technologies 5975T LTM GC/MSD Скачать руководство пользователя страница 223

Electronics

14

Troubleshooting and Maintenance Guide

223

MSD Power Supplies

Low voltage (AC-DC) MSD power supply

The low voltage MSD power supply is mounted next to the MSD 
toroid transformer in the MSD electronics module. A universal 
input power supply, it converts AC line voltage into the DC 
voltages used by the rest of the electronics. The power supply 
generates the following DC voltages:

•

+24 V (nominal)

•

+15 V (nominal)

•

–15 V (nominal)

•

+5 V (nominal)

High voltage (HED) power supply

The high voltage power supply provides the –10,000 volts DC for 
the high energy dynode (HED) in the detector for the EI MSD. 
The HED power supply also provides 600 VDC for the detector 
focus lens. Due to the high impedance of this circuit, measuring 
the detector focus voltage with a handheld voltmeter will give a 
typical reading of 90 to 100 volts where the polarity matches 
that of the HED voltage.

MSD toroid transformer

The MSD toroid transformer is mounted next to the AC board. It 
provides 24 VAC for the mass filter and source heater circuits. 
The input wires take 120 VAC or 200 to 260 VAC from the AC 
board. The AC board samples the line voltage and uses a relay to 
appropriately strap the toroid primary. The output wires 
connect to the main board.

Содержание 5975T LTM GC/MSD















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды