manualshive.com logo in svg

Agilent Technologies 5975T LTM GC/MSD, Руководство по устранению неисправностей и техническому обслуживанию

Поделиться
Скачать
Agilent Technologies 5975T LTM GC/MSD Скачать руководство пользователя страница 191

Vacuum System

12

Troubleshooting and Maintenance Guide

191

Side Plate

The side plate (

Figure 26

) covers the large opening in the side of 

the analyzer chamber. It is attached to the manifold with a 
hinge. The analyzer assembly is attached to the side plate inside 
the analyzer chamber. The hinge allows the side plate to swing 
away from the manifold for easy access to the analyzer.

Several electrical feedthroughs are built into the side plate. 
Wires connect the feedthroughs to analyzer components. The 
electronic side board is mounted on the atmospheric side of the 
side plate.

Thumbscrews are located at each end of the side plate.

C A U T I O N

Fasten both side plate thumbscrews for shipping or storage only. For 
normal operation, both thumbscrews should be loose. For operation 
with hydrogen carrier gas, or with flammable or explosive CI reagent 
gases, the front thumbscrew should be fastened just finger-tight. 
Overtightening will warp the side plate and cause air leaks. Do not 
use a tool to tighten the side plate thumbscrews.

C A U T I O N

When you turn on the power to pump down the MSD, be sure to 
press on the side board to ensure a good seal. 

Содержание 5975T LTM GC/MSD















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды