manualshive.com logo in svg

Agilent Technologies 5975T LTM GC/MSD, Руководство по устранению неисправностей и техническому обслуживанию

Поделиться
Скачать
Agilent Technologies 5975T LTM GC/MSD Скачать руководство пользователя страница 184

184

Troubleshooting and Maintenance Guide

12

Vacuum System

Common Vacuum System Problems

Air leak symptoms

The most common problems associated with any vacuum 
system are air leaks. Symptoms of air leaks include:

•

Loud gurgling noise from the foreline pump (very large 
leak.)

•

Inability of the turbo pump to reach 95% speed

•

Higher than normal high vacuum gauge controller readings

The 5975T LTM GC/MSD will 

not

 pump down successfully 

unless you press on the side plate (analyzer door) when you 
turn on the instrument power. Continue to press until the sound 
from the foreline pump becomes quieter.

Pumpdown failure shutdown

The system will shut down both the high vacuum and the 
foreline pump if the turbo pump speed is below 80% after 
7 minutes.

This is usually because of a 

large

 air leak: either the side plate 

has not sealed correctly or the vent valve is still open. This 
feature helps prevent the foreline pump from sucking air 
through the system, which can damage the analyzer and pump.

To restart the instrument, find and correct the air leak, then 
switch the power off and on. Be sure to press on the side plate 
when turning on the instrument power to ensure a good seal.

Содержание 5975T LTM GC/MSD















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды