manualshive.com logo in svg

Agilent Technologies 5975T LTM GC/MSD, Руководство по устранению неисправностей и техническому обслуживанию

Поделиться
Скачать
Agilent Technologies 5975T LTM GC/MSD Скачать руководство пользователя страница 158

158

Troubleshooting and Maintenance Guide

10

General Maintenance

To Replace the Electron Multiplier Horn

Materials needed

•

Electron multiplier horn (G3170-80103)

•

Gloves, clean, lint-free

•

Large (8650-0030)

•

Small (8650-0029)

Procedure

1

Vent the instrument. 

2

Open the analyzer chamber. 

3

Open the retaining clip (

Figure 19

). Lift the arm of the clip 

up and then swing the clip away from the electron multiplier 
horn.

4

Remove the electron multiplier horn.

5

Install the new electron multiplier horn.

6

Close the retaining clip.

The signal pin on the horn must rest 

on the outside

 of the 

loop in the contact strip. 

Do not

 put the signal pin on the 

inside of the loop in the contact strip. Incorrect installation 
will result in poor sensitivity or no signal.

7

Close the analyzer chamber. 

    

            

Содержание 5975T LTM GC/MSD















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды