Agilent Technologies 5975T LTM GC/MSD Скачать руководство пользователя страница 151

Страница: 151 / 270

General Maintenance

Troubleshooting and Maintenance Guide

151

To Reinstall a Filament

Materials needed

•

Filament assembly (G2590-60053)

•

Gloves, clean, lint-free

•

Large (8650-0030)

•

Small (8650-0029)

•

Hex ball driver, 1.5 mm (8710-1570)

Procedure

Install the new filament (

Figure 16

Remove the screw holding the filament to the ion source
body.

Slide off the filament assembly.

Orient the assembly so that the filament is next to the ion
source body.

Replace the screw to the ion source body.

After installing the filament, verify that it is not grounded to
source body.

Reinstall the ion source. See the

“To Reinstall the EI Ion

Source”

on page 148.

Close the analyzer chamber.

Pump down the MSD.

Autotune the MSD.

In the

Edit Parameters

dialog box (

Instrument/Edit MS Tune

Parameters

), select the other filament.

Autotune the MSD again.

Select and use the filament that gives the best results.

If you decide to use the first filament, run Autotune again to
make sure the tune parameters are compatible with the
filament.

Select

Save Tune Parameters

from the

File

menu.





Содержание 5975T LTM GC/MSD















































































































































































































































































Результаты поиска

Содержание 5975T LTM GC/MSD

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies 5975T LTM GC/MSD, Руководство по устранению неисправностей и техническому обслуживанию

Результаты поиска

Содержание 5975T LTM GC/MSD

Отзывы:

Бренды по названию

Популярные бренды