manualshive.com logo in svg

Agilent Technologies 5975T LTM GC/MSD, Руководство по устранению неисправностей и техническому обслуживанию

Поделиться
Скачать
Agilent Technologies 5975T LTM GC/MSD Скачать руководство пользователя страница 133

General Maintenance

10

Troubleshooting and Maintenance Guide

133

To Lubricate the Side Plate O-Ring

Materials needed

•

Cloths, clean (05980-60051)

•

Gloves, clean, lint-free

•

Large (8650-0030)

•

Small (8650-0029)

•

Grease, Apiezon L, high vacuum (6040-0289)

The side plate O-ring needs a thin coat of grease to ensure a 
good vacuum seal. If the side plate O-ring appears dry or does 
not seal correctly, lubricate it using this procedure. A good test 
is to wipe off the side plate with methanol, then close the 
analyzer chamber. If the O-ring has enough grease on it, it will 
leave a faint trace on the side plate.

Procedure

1

Vent the instrument. 

2

Open the analyzer chamber. (See the 

5975T LTM GC/MSD 

Operation Manual

).

3

Remove the analyzer by disconnecting the source wiring, 
and loosening the sideboard from the hinge. (See the 

5975T 

LTM GC/MSD Operation Manual

).

4

Use a clean, lint-free cloth or glove to spread a 

thin

 coat of 

high vacuum grease only on the exposed surface of the 
O-ring (

Figure 9

).

5

Use a clean, lint-free cloth or glove to wipe away excess 
grease. If the O-ring looks shiny, there is too much grease on 
it.

C A U T I O N

Vacuum seals other than the side plate O-ring and vent valve O-ring 
do not need to be lubricated. Lubricating other seals can interfere 
with their correct function.

    

            

C A U T I O N

Do not use anything except the recommended vacuum grease. 
Excess grease can trap air and dirt. Grease on surfaces of the O-ring 
other than the exposed surface can trap air, resulting in air spikes 
during operation.

Содержание 5975T LTM GC/MSD















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды