Agilent Technologies 5975T LTM GC/MSD Скачать руководство пользователя страница 129

Страница: 129 / 270

General Maintenance

Troubleshooting and Maintenance Guide

129

To Reinstall the EI Calibration and Vent Valve Assembly

Materials needed

•

Calibration valve (G3170-60204)

•

O-ring for calibration valve (0905-1217)

•

PFTBA (05971-60571) or other tuning compound

•

Screwdriver, Torx T-15 (8710-1622)

Procedure

Remove the old valve assembly. See

page 128

and

Figure 7

Be sure the valve O-ring is in place. If it is worn or damaged,
replace it.

Install the calibration and vent valve assembly and tighten
the screws that hold it in place.

Reconnect the calibration valve cable to the connector next
to the fan.

Remove the vial from the new calibration valve. See

page 128

. The valve is supplied with a vial already installed.

Fill and reinstall the calibration vial. See

page 125

Pump down the MSD.

Select

Purge Calibrant Valve

from the

Vacuum

menu in the

Tune

and Vacuum Control

view.





C A U T I O N

Failure to purge the calibration valve will damage the filaments and
detector.

Содержание 5975T LTM GC/MSD















































































































































































































































































Результаты поиска

Содержание 5975T LTM GC/MSD

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies 5975T LTM GC/MSD, Руководство по устранению неисправностей и техническому обслуживанию

Результаты поиска

Содержание 5975T LTM GC/MSD

Отзывы:

Бренды по названию

Популярные бренды