Agilent Technologies 34945A Скачать руководство пользователя страница 98

Страница: 98 / 124

Agilent 34945A Microwave Switch/Attenuator Driver Module User’s Guide

Additional Operating Information

34945A SCPI Command Summary

Table 5-1 lists the SCPI commands that apply to the 34945A RF Switch
Platform.

As not all commands are covered in this manual, refer to the Programmer’s
Reference contained on the 34980A Product Reference CD-ROM (p/n
34980-13601) for detailed information on the complete SCPI command set.

Table 5-1. 34945A SCPI Command Summary.

Subsystem

Commands

ROUTe

(Switch Control)

ROUTe:CHANnel:DRIVe:CLOSe:DEFault (@<ch_list>)

ROUTe:CHANnel:DRIVe:CLOSe:DEFault? (@<ch_list>)
ROUTe:CHANnel:DRIVe:OPEN:DEFault (@<ch_list>)

ROUTe:CHANnel:DRIVe:OPEN:DEFault? (@<ch_list>)
ROUTe:CHANnel:DRIVe:PAIRed[:MODE] {OFF|0|ON|1}, (@<ch_list>)

ROUTe:CHANnel:DRIVe:PAIRed[:MODE]? (@<ch_list>)
ROUTe:CHANnel:DRIVe:PULSe[:MODE] {OFF|0|ON|1}, (@<ch_list>)

ROUTe:CHANnel:DRIVe:PULSe[:MODE]? (@<ch_list>)
ROUTe:CHANnel:DRIVe:PULSe:WIDTh {<seconds>|MIN|MAX|DEF},

(@<ch_list>)

ROUTe:CHANnel:DRIVe:PULSe:WIDTh? [{MIN|MAX}, ] (@<ch_list>)

ROUTe:CHANnel:DRIVe:STATe? (@<ch_list>)

ROUTe:CHANnel:DRIVe:TIME:RECovery {<seconds> |MIN|MAX|DEF},
(@<ch_list>)

ROUTe:CHANnel:DRIVe:TIME:RECovery? [{MIN|MAX}, ] (@<ch_list>)
ROUTe:CHANnel:DRIVe:TIME:SETTle {<seconds>|MIN|MAX|DEF},

(@<ch_list>)

ROUTe:CHANnel:DRIVe:TIME:SETTle? [{MIN|MAX}, ] (@<ch_list>)

ROUTe:CHANnel:LABel:CLEar:MODule <slot | ALL>
ROUTe:CHANnel:LABel[:DEFine] "<label>" , (@<ch_list>)

ROUTe:CHANnel:LABel[:DEFine]? [<type>,] (@<ch_list>)
ROUTe:CHANnel:VERify[:ENABle] {OFF|0|ON|1}, (@<ch_list>)

ROUTe:CHANnel:VERify[:ENABle]? (@<ch_list>)

ROUTe:CHANnel:VERify:POLarity {NORMal|INVerted}, (@<ch_list>)
ROUTe:CHANnel:VERify:POLarity? (@<ch_list>)

ROUTe:CHANnel:VERify:POSition:STATe? (@<ch_list>)
ROUTe:CLOSe (@<ch_list>)

ROUTe:CLOSe? (@<ch_list>)
ROUTe:MODule:BUSY? {1|ANY}

ROUTe:MODule:WAIT <slot | ALL>
ROUTe:MODule:WAIT? <slot | ALL>

ROUTe:OPEN (@<ch_list>)
ROUTe:OPEN? (@<ch_list>)

ROUTe:OPERation:OVERlap[:ENABle] {OFF|0|ON|1}

ROUTe:OPERation:OVERlap[:ENABle]?

Содержание 34945A





























































































































Результаты поиска

Содержание 34945A

Отзывы:

Похожие инструкции для 34945A

Бренды по названию

Популярные бренды

Agilent Technologies 34945A, Руководство пользователя

Результаты поиска

Содержание 34945A

Отзывы:

Похожие инструкции для 34945A

Бренды по названию

Популярные бренды