Agilent Technologies 34945A Скачать руководство пользователя страница 70

Страница: 70 / 124

Agilent 34945A Microwave Switch/Attenuator Driver Module User’s Guide

Introduction to Programming

This feature is limited to external channel drive sources (power supplies)
with the capability to drive multiple channels.

• boot/reset channel drive

- this parameter specifies the channel drive

source setting following a re-boot (power-up) or reset of the instrument.

Switch/Attenuator Channel Configuration Window

The switch/attenuator channel configuration window is opened by right-click-

ing near the ‘IsOpen’ or ‘IsClosed’ labels on the ‘programming diagram’.

Figure 4-4. The Switch/Attenuator Channel Configuration Window.

The configuration window applies to the

individual

channels on the distribu-

tion board. The parameters of this window include:

• operation mode

- enables channel pairing for dual-coil devices.

• channel state after boot or Reset

- specifies the channel state (opened,

closed) following power-on or reset (assumes boot/reset channel drive state
is set).

• activation type

- specifies pulsed or continuous drive current.

• pulse width

- specifies the pulse width of the drive current.

• recovery time

- specifies the period between activation pulses

Содержание 34945A





























































































































Результаты поиска

Содержание 34945A

Отзывы:

Похожие инструкции для 34945A

Бренды по названию

Популярные бренды

Agilent Technologies 34945A, Руководство пользователя

Результаты поиска

Содержание 34945A

Отзывы:

Похожие инструкции для 34945A

Бренды по названию

Популярные бренды