Agilent Technologies 34945A Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 124

background image

46

Agilent 34945A Microwave Switch/Attenuator Driver Module User’s Guide

3

Software Installation and Configuration

Configuring the GPIB Interface

Programming access to the 34980A is also available through the instrument’s
optional GPIB interface. The GPIB connector is located on the rear panel of
the instrument. Simultaneous LAN and GPIB connections to the instrument
are allowed. The following information describes how instruments on the GPIB
interface are configured using Agilent Connection Expert.

GPIB Connections

GPIB cables can be connected to the PC in a “star” (all cables connect directly

to the computer) or “linear” (instrument to instrument) configuration.

Starting Agilent Connection Expert

Start Connection Expert by clicking the Agilent Control icon and selecting

“Agilent Connection Expert” from the pop-up menu (Figure 3-2). If a GPIB

card is installed in your computer, the (GPIB) interface was configured during

installation of the Agilent IO libraries and is displayed in the left column

(

Explorer

pane) of the “welcome” screen (Figure 3-6).

N O T E

The following information assumes a GPIB interface card has been installed in
your computer.

The 34980A is an Agilent web-enabled instrument that offers a user interface
which requires no user-installed IO drivers. Access to the instrument via the Web
interface, however, is only available through the LAN connection.

«
...
52
53
54
55
56
...
»

Содержание 34945A





























































































































Отзывы:

Нет отзывов

Похожие инструкции для 34945A

DGS-3224TGR - Switch

Бренд: D-Link Страницы: 160

Бренд: D-Link Страницы: 145

DGS-1510 Series

Бренд: D-Link Страницы: 64

DES-3528 - xStack Switch - Stackable

Бренд: D-Link Страницы: 367

RackSwitch G8264T

Бренд: IBM Страницы: 20

Бренд: D-Link Страницы: 17

Sierra Pro XL 1616V3

Бренд: Kramer Страницы: 2

Pow-R-Line SPX0361126

Бренд: Eaton Страницы: 584

Бренд: Datavideo Страницы: 38

Бренд: Key Digital Страницы: 20

Бренд: EtherWAN Страницы: 2

Бренд: EtherWAN Страницы: 2

Бренд: Campbell Hausfeld Страницы: 4

Nivotester FTC325

Бренд: Endress+Hauser Страницы: 40

LMP-0602 24-V2 Series

Бренд: ANTAIRA Страницы: 2

Бренд: Key Digital Страницы: 20

Бренд: AT&T Страницы: 24

Бренд: Wyrestorm Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды