Agilent Technologies 1290 Infinity II 2D-LC Solution Скачать руководство пользователя страница 292

Страница: 292 / 395

Troubleshooting and Diagnostics

Lab Advisor Service

Diagnostic

2D-LC User Guide

292

Replace the Module Firmware

When

The installation of newer firmware might be necessary

•

if a newer version solves problems of older versions or

•

to keep all systems on the same (validated) revision.

The installation of older firmware might be necessary

•

to keep all systems on the same (validated) revision or

•

if a new module with newer firmware is added to a system or

•

if third party control software requires a special version.

Tools required

Description

Agilent Lab Advisor software

Parts required

Description

Firmware, tools and documentation from Agilent web site

Preparations

Read the following:

•

Documentation provided with the Agilent Lab Advisor online help

•

2D-LC Manual

Procedure to follow:

•

Close the current Acquisition client window

•

Close instrument connection from OpenLab Control Panel

NOTE

Do not mix firmware files from different firmware sets.

Содержание 1290 Infinity II 2D-LC Solution












































































































































































































































































































































































































Результаты поиска

Содержание 1290 Infinity II 2D-LC Solution

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies 1290 Infinity II 2D-LC Solution, Руководство пользователя

Результаты поиска

Содержание 1290 Infinity II 2D-LC Solution

Отзывы:

Бренды по названию

Популярные бренды