AGI Westeel EasyFlow2 100 Series Скачать руководство пользователя

Страница: 8 / 74

BU-0101704 R3

2.5.1 Electric Motor Safety

Power Source

• Electric motors and controls shall be installed and serviced by

a qualified electrician and must meet all local codes and
standards.

• Use a magnetic starter to protect the electric motor.

• You must have a manual reset button.

• Reset and motor starting controls must be located so that the

operator has full view of the entire operation.

• Locate main power disconnect switch within reach from

ground level to permit ready access in case of an emergency.

• Motor must be properly grounded.

• Ensure electrical wiring and cords remain in good condition;

replace if necessary.

S E R V I C E D I S C O N N E C T

OFF

Lockout

• The main power disconnect switch should be in the locked position during shutdown or

whenever maintenance is performed.

• If reset is required, disconnect all power before resetting motor.

2.6. Personal Protective Equipment

The following Personal Protective Equipment (PPE) should be worn when assembling the equipment.

Safety Glasses

• Wear safety glasses at all times to protect eyes from debris.

Work Gloves

• Wear work gloves to protect your hands from sharp and rough edges.

Steel-Toe Boots

• Wear steel-toe boots to protect feet from falling debris.

Coveralls

• Wear coveralls to protect skin.

2. SAFETY

EASYFLOW2 (100 SERIES) – FARM TUBE BIN UNLOAD SYSTEM

Содержание Westeel EasyFlow2 100 Series











































































Результаты поиска

Содержание Westeel EasyFlow2 100 Series

Отзывы:

Похожие инструкции для Westeel EasyFlow2 100 Series

Бренды по названию

Популярные бренды

AGI Westeel EasyFlow2 100 Series, Сборка и инструкция по установке

Результаты поиска

Содержание Westeel EasyFlow2 100 Series

Отзывы:

Похожие инструкции для Westeel EasyFlow2 100 Series

Бренды по названию

Популярные бренды