manualshive.com logo in svg

AGI Westeel EasyFlow2 100 Series, Сборка и инструкция по установке

Поделиться
Скачать
AGI Westeel EasyFlow2 100 Series Скачать руководство пользователя страница 7

BU-0101704 R3

7

2.3. Rotating Flighting Safety

• KEEP AWAY from rotating flighting.

• DO NOT remove or modify flighting guards, doors, or covers.

Keep in good working order. Have replaced if damaged.

• DO NOT operate the bin unload without all guards, doors,

and covers in place.

• NEVER touch the flighting. Use a stick or other tool to

remove an obstruction or clean out.

• Shut off and lock out power to adjust, service, or clean.

2.4. Rotating Parts Safety

• Keep body, hair, and clothing away from rotating pulleys,

belts, chains, and sprockets.

• Do not operate with any guard removed or modified. Keep

guards in good working order.

• Shut off and lock out power source before inspecting or

servicing machine.

2.5. Drives and Lockout Safety

Inspect the power source(s) before using and know how to shut down in an emergency.
Whenever you service or adjust your equipment, make sure you shut down the power
source and follow lockout and tagout procedures to prevent inadvertent start-up and
hazardous energy release. Know the procedure(s) that applies to your equipment from the
following power source(s). Ensure that only 1 key exists for each assigned lock, and that
you are the only one that holds that key. Ensure that all personnel are clear before turning
on power to equipment.

WARNING

EASYFLOW2 (100 SERIES) – FARM TUBE BIN UNLOAD SYSTEM

2. SAFETY

Содержание Westeel EasyFlow2 100 Series











































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды