AGI Batco BCX2 страница 8 Скачать руководство пользователя

Страница: 8 / 54

8210-00001 R0

2.4. Moving Conveyor Belt Safety

• DO NOT step on or touch moving conveyor belt.

• Shut off and lock out power to adjust, service, or clean.

2.5. Upending

• Anchor intake end and/or support discharge end to prevent

upending.

• Intake end must always have downward weight. Do not

release until attached to tow bar or resting on ground.

• Do not raise intake end above tow bar height.

• Empty the conveyor and fully lower before moving.

2.6. Rotating Parts Safety

• Keep body, hair, and clothing away from rotating pulleys,

belts, chains, and sprockets.

• Do not operate with any guard removed or modified. Keep

guards in good working order.

• Shut off and remove key or lock out power source before

inspecting or servicing machine.

2.7. Work Area Safety

• Have another trained person nearby who can shut down the conveyor in case of accident.

• The work area should be kept clear of bystanders, including children.

• Keep the work area clean and free of debris.

2. SAFETY

PTO TOP-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR

Содержание Batco BCX2























































Результаты поиска

Содержание Batco BCX2

Отзывы:

Похожие инструкции для Batco BCX2

Бренды по названию

Популярные бренды

AGI Batco BCX2, Руководство оператора

Результаты поиска

Содержание Batco BCX2

Отзывы:

Похожие инструкции для Batco BCX2

Бренды по названию

Популярные бренды