AGI Batco BCX2 страница 41 Скачать руководство пользователя | Manualshive

Страница: 41 / 54

background image

8210-00001 R0

41

Figure 13.

Top Drive Pinch Roller

7.11. Align the Conveyor Belt

Basic Conveyor Belt Alignment:

The conveyor belt will run straight when all of the rollers are straight.

Loosen or tighten the adjustment bolt(s) to align the conveyor belt. Tighten the side the belt has moved toward,
or loosen the side the belt has moved away from.

Figure 14.

Roller out of Alignment

OR

LOOSEN

TIGHTEN

TIGHTEN FULLY

DO NOT TIGHTEN

PTO TOP-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR

«
...
39
40
41
42
43
...
»

Содержание Batco BCX2























































Отзывы:

Нет отзывов

Похожие инструкции для Batco BCX2

Бренд: Calira Страницы: 14

Бренд: Eaton Страницы: 21

Бренд: AC Schnitzer Страницы: 16

Бренд: NCR Страницы: 8

Бренд: Waterford Страницы: 16

BTL7-S5 B-M Series

Бренд: Balluff Страницы: 14

BML-S1G0 7 M5E 0 Series

Бренд: Balluff Страницы: 194

Бренд: Rally Pack Страницы: 2

Бренд: rako Страницы: 3

smartsensor advance

Бренд: Wavetronix Страницы: 2

Бренд: X-lite Страницы: 5

Бренд: Yolink Страницы: 27

Бренд: Ikan Страницы: 2

Бренд: PullRite Страницы: 10

Бренд: Viking Страницы: 1

signal mirror 2005-2009 Ford Mustang

Бренд: muth Страницы: 9

Бренд: Soehnle Страницы: 20

Бренд: TeraBee Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды