AGI 1549 Скачать руководство пользователя страница 9

Страница: 9 / 122

8210-10003 R0

1.8. Hand Winch Safety

When Equipped:

• Inspect lift cable before using. Replace if frayed or damaged. Make sure lift cable is seated

and tracking properly and cable clamps are secure.

• Tighten brake lock by turning winch handle clockwise at least two clicks after lowering the

conveyor.

• Lower the conveyor fully before towing, then rotate winch handle until cable has light

tension.

• Do not lubricate winch brake discs.

1.9. Hydraulic Winch Safety

When Equipped:

• Keep away from rotating cable drum and winch cable. Do not touch or grab cable while

winch is being operated or use hands to guide the cable.

• Inspect cable and cable clamps before using hydraulic winch. Replace cable if frayed or

damaged. Tighten cable clamps if necessary.

• Check the cable anchor on the winch drum is tight.

• Confirm hydraulic hoses are in good condition.

• Do not continue to supply power to hydraulic winch after the conveyor has reached full up

position.

• Do not disconnect hydraulic quick couplers when lines are pressurized.

• Make sure lift cable is seated properly.

• Always keep a minimum of 3 cable wraps on the cable drum.

UCX3 S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR

1. SAFETY

Содержание 1549



























































































































Результаты поиска

Содержание 1549

Отзывы:

Бренды по названию

Популярные бренды

AGI 1549, Инструкция по сборке

Результаты поиска

Содержание 1549

Отзывы:

Бренды по названию

Популярные бренды