AGI 1549 Скачать руководство пользователя страница 19

Страница: 19 / 122

8210-10003 R0

3.6. Assemble the Remainder of the S-Drive

Note

The s-drive normally comes mostly pre-assembled when delivered from the factory. The steps below are
the remaining assembly which must be performed.

For each side of the s-drive:

1. Remove the lock collar (2) and hex nuts (6) from the pretensioner assembly.

Note

The pretensioner assembly (1) is comprised of the threaded rod weldment, pretensioner pipe,
spring, lock collar, and two hex nuts. This is factory pre-assembled.

2. Position a hex nut (6) on each side of the slider weldment.

3. Thread the pretensioner assembly (1) through the spring capture plate (3), hex nuts in the slider weldment

(4), and roller in the bolt on pretensioner tab (5).

4. Re-fasten the lock collar (2).

Note

The s-drive bottom guard and take-up bolt guard will be assembled onto the conveyor later, after
belt tensioning and alignment. See

Section 3.25 – Attach the S-Drive Bottom and Take-up Side

Guards on page 87

Installing the Take-up Roller Bolt Assembly

Pretensioner Assembly

Slider Weldment

Lock Collar

Pretensioner Tab

Spring Capture Plate

3/4" Hex Nut UNC GR8 ZN

UCX3 S-DRIVE FIELD LOADER – PORTABLE GRAIN BELT CONVEYOR

3. ASSEMBLY

Содержание 1549



























































































































Результаты поиска

Содержание 1549

Отзывы:

Бренды по названию

Популярные бренды

AGI 1549, Инструкция по сборке

Результаты поиска

Содержание 1549

Отзывы:

Бренды по названию

Популярные бренды