manualshive.com logo in svg

AGFA DRYSTAR AXYS, Руководство по обслуживанию

Поделиться
Скачать
AGFA DRYSTAR AXYS Скачать руководство пользователя страница 270

 
 
DD+DIS033.07E 

Repair and Service

Adjustments and Calibrations

 
 
 

 

DOCUMENT CONTROL NOTE: 

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled. 

Edition 1, Revision 1 

DRYSTAR AXYS 

Chapter 3.6 / 18 

06-2008 Type 

5367/100 

Agfa Company Confidential

 

2.5 

Compliance Film Calibration as part of Afssaps / EUREF Calibration 
Procedure 

 

WHEN TO BE 
PERFORMED 

The compliance film calibration may be required as last step of the Afssaps / EUREF* 
calibration procedure for a DRYSTAR AXYS used for printing mammo images. 

The Afssaps / EUREF compliance calibration procedure has to be performed in 
following cases: 

•

 

Before the Afssaps / EUREF mammo acceptance test. 

•

 

Each 6 months, if the printer is under control of Afssaps / EUREF, and it did not 
pass the Afssaps / EUREF calibration check (see section 2.5.6). 

 =  

Agence française de sécurité sanitaire des produits de santé 

 

European Reference Organisation for Quality Assured Breast Screening and  

 Diagnostic 

Services

 

 

 

PREREQUISITE 

1)  The compliance film calibration is only 

available for DRYSTAR AXYS 
software 

≥

 1.6.2_C1. 

2)  A “TG18-PQC modified 4” image has 

to be available on the modality. 
 
The Test Pattern can be downloaded 
from 

 

 

 

Figure 10: TG18-PQC modified 4 

 

 

PURPOSE 

Make film calibration this accurate, that it passes the acceptance criteria as defined 
by Afssaps / EUREF: 
The default film calibration procedure is not necessarily accurate enough.  

 

Содержание DRYSTAR AXYS














































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды