AGCO LELY ATTIS PT 130 Скачать руководство пользователя страница 79

Страница: 79 / 98

5.1 Replace the transport wheel

WARNING: Risk of injury

Make sure that there are no persons in the area when you move the machine to the
transport position.

Procedure

Push button

and lower the loader arm to the ground.

Make sure that the transport wheel is not in contact with the ground.

Make sure that you lock the clip (1) into pin

(2).

GUID-7B2C04B7-CD93-4BE9-8C1E-E95E370950F6-high.jpg [High]

Fig. 1

Remove clip (1) and pin (2) then rotate the

wheel assembly 180

GUID-8105BCD3-7514-479F-B888-1F94833EB963-high.jpg [High]

Fig. 2

Loosen and remove the wheel nuts and then

remove the transport wheel from the

machine.

GUID-AA4E2189-8B74-4899-A831-9ACF799EEF90-high.jpg [High]

Fig. 3

GUID-EA6B9B7B-6E1D-44D0-9F65-1C105AD02703 [V1]

5. Troubleshooting

Bale Wrapper

4820.LE.EN01

Содержание LELY ATTIS PT 130


































































































Результаты поиска

Содержание LELY ATTIS PT 130

Отзывы:

Бренды по названию

Популярные бренды

AGCO LELY ATTIS PT 130, Руководство оператора

Результаты поиска

Содержание LELY ATTIS PT 130

Отзывы:

Бренды по названию

Популярные бренды