AGA DC3 Скачать руководство пользователя | Manualshive

Страница: 12 / 24

background image

ROOM VENTED MODELS

Fig. 7

DESN 516752

VENT UNDER SHROUD TO

BE LEFT OPEN

NOTE:

ON ROOM VENT MODEL COPPER

END CAP TO BE PUSHED IN PLACE ON

INSTALLATION

12

Room Vented Models

It is recommended that this model is fitted in conjunction with a cooker hood. The AGA oven
venting outlet is located on the top of the AGA between the two hotplates., and is designed for
venting the moisture from the ovens. The cooker hood should be positioned not less than the
minimum height as recommended by the manufacturer, from the top of the AGA.

These are 650mm for AGA Rext 720

650mm for AGA 1000 SE

«
...
10
11
12
13
14
...
»

Содержание DC3

























Отзывы:

Нет отзывов

Похожие инструкции для DC3

Бренд: Gaggenau Страницы: 19

Profile PHP900DM

Бренд: GE Страницы: 1

Бренд: Oster Страницы: 16

Бренд: Salton Страницы: 5

Бренд: Omega Страницы: 12

Бренд: Gaggenau Страницы: 20

Бренд: GE Страницы: 36

Party Crock 840149600

Бренд: Hamilton Beach Страницы: 52

Бренд: Hotpoint Страницы: 64

Mista Aesthetic B601GMXI9

Бренд: Smeg Страницы: 40

Бренд: Tenneker Страницы: 80

CookSmart CET366TB

Бренд: Thermador Страницы: 72

PolyScience HydroPro Plus GSV750

Бренд: Sage Страницы: 116

Бренд: Omega Страницы: 32

Egg Cooker De Luxe

Бренд: Nova Страницы: 12

Бренд: Jenn-Air Страницы: 11

Бренд: Pit Boss Страницы: 118

Бренд: Vigan Mammoth Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды