manualshive.com logo in svg

AG Neovo K Series, Руководство пользователя, Страница: 18 / 22

Поделиться
Скачать
AG Neovo K Series Скачать руководство пользователя страница 18

 

17

ERROR  MESSAGE & POSSIBLE  SOLUTION 

CABLE NOT CONNECTED : 

1.  Check that the signal-cable is properly connected, If the connector is 

loose, tighten the connector’s screws. 

2.  Check the signal-cable’s connection pins for damage. 

 

INPUT NOT SUPPORT : 

Your computer has been set to unsuitable display mode, set the computer to 

display mode given in the following table. 

 

Disposal of Waste Equipment by Users in Private Household in the 

European Union. This symbol on the product or on its packaging 

indicates that this product must not be disposed of with your other 

household waste.    Instead, it is your responsibility to dispose of 

your waste equipment by handing it over to a designated collection 

point for the recycling of waste electrical and electronic equipment.   

The separate collection and recycling of your waste equipment at 

the time of disposal will help to conserve natural resources and 

ensure that it is recycled in a manner that protects human health 

and the environment. For more information about where you can 

drop off your waste equipment for recycling, please contact your 

local city office, your household waste disposal service or the shop 

where you purchased the product. 

 

SAFETY: Lamp Disposal 

  LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST 

BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR 

FEDERAL LAWS. FOR MORE INFORMATION, CONTACT THE 

ELECTRONIC INDUSTRIES ALLIANCE AT 

WWW.EIAE.ORG

. 

Vermont Hg directive 

Title 10: Conservation and Development 
Chapter 164: COMPREHENSIVE MERCURY MANAGEMENT 
§ 7106. Labeling of mercury-added products 

Contains Mercury, Dispose of Properly 

Содержание K Series























Отзывы:

Нет отзывов