Aficio 2404WD Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 92

Aficio 2404WD Скачать руководство пользователя страница 37

When a Message Appears

31

3

Alert Messages

This section describes the machine Alert messages.

Message

Cause

Solution

Cannot connect

with the wireless

card. Turn the

main power switch

off, then check

the card.

IEEE 802.11b interface
unit was not inserted
when the machine was
turned on.

Turn off the machine and check the in-
terface unit is inserted correctly. Then,
turn the machine on again. If the mes-
sage appears again, call your service
representative.

Cannot connect

with the wireless

card. Turn the

main power switch

off, then check

the card.

IEEE 802.11b interface
unit was pulled out after
the machine turned on.

Turn off the machine and check the in-
terface unit is inserted correctly. Then,
turn the machine on again. If the mes-
sage appears again, call your service
representative.

Problems with the

wireless card.

A wireless card that the
machine cannot use has
been installed.

Turn off the machine and check the in-
terface unit is inserted correctly. Then,
turn the machine on again. If the mes-
sage appears again, call your service
representative.

Problems with the

wireless board.

Access to the wireless
board in which the IEEE
802.11b interface unit is
inserted is possible, but
an error was detected.

Turn off the machine and check the in-
terface unit is inserted correctly. Then,
turn the machine on again. If the mes-
sage appears again, call your service
representative.

Problem with Hard

Disk.

An error has occurred in
the hard disk drive.

Turn off the main power switch, and back
on again. If the message appears again,
contact your service representative.

The entered pass-

word is incor-

rect.

The password of the en-
crypted PDF file has
been entered incorrectly.

Enter the correct password.

Error has oc-

curred.

A syntax error, etc., has
occurred.

Check the PDF file is not corrupted.

USB has a prob-

lem.

An error has occurred in
the USB interface.

Turn off the main power switch, and back
on again. If the message appears again,
contact your service representative.

Hardware Problem:

Ethernet

An error has occurred in
the Ethernet board.

Turn off the main power switch, and back
on again. If the message appears again,
contact your service representative.

Printing privi-

leges have not

been set for this

document.

You tried to print a print-
protected document.

You cannot print this document.

«
...
35
36
37
38
39
...
»

Содержание 2404WD





























































































Отзывы:

Нет отзывов