Afag 50315434 Скачать руководство пользователя страница 21

Страница: 21 / 66

Operating instructions EN

◼

SE-24

◼

01.06.2022

◼

V1.5

–66

4 Product description

4.1 Basic information

The devices of the SE-24 series are ultra compact four quadrant controllers in the
protection class IP65 which can be installed outside the switch cabinet.

They are suitable for brushless motors and motors with brushes and were especially
designed for the drive of Afag handling components.

The control variant can be seen from the designation of the devices.

SE-24 Profibus

Control

Intermediate circuit voltage

Type designation

Figure 1: Type code

The servo controllers of the SE-24 series are available with the following control
variants:

Type

Order No.

Control

SE-24 I/O

50315434

Digital inputs and outputs

SE-24 Profibus

50315435

PROFIBUS fieldbus

SE-24 EtherCAT

50315436

EtherCAT fieldbus

SE-24 CANopen

50315437

CANopen fieldbus

Содержание 50315434



































































Результаты поиска

Содержание 50315434

Отзывы:

Бренды по названию

Популярные бренды

Afag 50315434, Руководство по эксплуатации

Результаты поиска

Содержание 50315434

Отзывы:

Бренды по названию

Популярные бренды