manualshive.com logo in svg

Aerotech Ndrive ML Series, Руководство по оборудованию

Поделиться
Скачать
Aerotech Ndrive ML Series Скачать руководство пользователя страница 49

Installation and Configuration

Ndrive ML

2.4.3. Thermistor Interface (J103)

The thermistor input is used to detect a motor over temperature condition by using a positive temperature
coefficient sensor. As the temperature of the sensor increases, so does the resistance. Under normal
operating conditions, the resistance of the thermistor is low (i.e., 100 ohms) which will result in a low input
signal. As the increasing temperature causes the thermistor’s resistance to increase, the signal will be seen
as a logic high triggering an over temperature fault. The nominal trip value of the sensor is 1k Ohm.

Table 2-19:

Thermistor Pin on the Motor Feedback Connector (J103)

Pin#

Description

In/Out/Bi

2

Motor Over Temperature Thermistor

Input

Figure 2-22:

Thermistor Interface Input (J103)

www.aerotech.com

Chapter 2

49

Содержание Ndrive ML Series





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды