manualshive.com logo in svg

Aerotech Ndrive ML Series, Руководство по оборудованию

Поделиться
Скачать
Aerotech Ndrive ML Series Скачать руководство пользователя страница 42

42

Chapter 2

www.aerotech.com

2.4.1. Encoder Interface (J103)

The Ndrive ML is equipped with standard and auxiliary encoder feedback channels. The standard encoder
interface is accessible through the Motor Feedback (J103) connector. The standard encoder interface will
accept an RS-422 differential line driver signal. If the Ndrive ML has been purchased with the -MXH or -MXU
option, the standard encoder interface can be configured for an analog encoder input via parameter settings.

Refer to

Section 2.4.1.3.

for encoder feedback phasing.

N O T E :

 Encoder wiring should be physically isolated from motor, AC power, and all other power wiring.

N O T E :

 The PSO feature is

not

compatible with the -MXU option. The PSO feature operates with the -

MXH option and with square wave encoders.

Table 2-15:

Encoder Interface Pins on the Motor Feedback Connector (J103)

Pin#

Description

In/Out/Bi

1

Chassis Frame Ground

N/A

3

+5V Power for Encoder (500 mA max)

Output

6

Encoder Marker Reference Pulse -

Input

7

Encoder Marker Reference Pulse +

Input

14

Encoder 

Input

15

Encoder Cosine -

Input

17

Encoder Sine +

Input

18

Encoder Sine -

Input

21

Signal Common for Encoder

N/A

Ndrive ML

Installation and Configuration

Содержание Ndrive ML Series





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды