Aerotech Ndrive HPe 100 Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 114

background image

-IO Expansion Board

Ndrive HPe 50/75/100

3.8. SSINET (J302/J303)

The SSINet is designed for daisy-chaining encoder signals from one Ndrive HPe 50/75/100 to another for
two/three-axis PSO (laser firing). This allows one Ndrive HPe 50/75/100 containing the -DUALPSO or -
TRIPLEPSO options to track the vectorial position change of two/three axes in real-time. These encoder
signals may also be used for user-defined purposes. Refer to

and

. These four

channels are bi-directional and configured via the SSINet1Setup and SSINet2Setup parameters; refer to the
A3200 Help File for more information. The signals from these ports will be the same as the differential line
driver encoder signal input to the Ndrive HPe 50/75/100, unless the -MXH option is present.

N O T E :

The SSINet #1 and #2 interfaces are both physically hardwired to the J302 and J303 connectors.

If SSINet #1 is configured as an input, a signal driven into the SSINet #1 connections on J302 will also be
present on the SSINet #1 connections of J303, effectively making SSINet #1 on J303 an (un-buffered) out-
put of this same signal. Likewise, this would also be true for the SSINet #2 interface.

Table 3-28:

2-Channel SSINet Connector Pinout (J302/J303)

Pin#

Description

In/Out/Bi

1

SSINet #1 Sin-N

Bidirectional

2

SSINet #1 Sin

Bidirectional

3

SSINet #2 Cosine-N / Marker-N

Bidirectional

4

SSINet #2 Sin-N

Bidirectional

5

SSINet #2 Sin

Bidirectional

6

SSINet #2 Cosine / Marker

Bidirectional

7

SSINet #1 Cosine-N / Marker-N

Bidirectional

8

SSINet #1 Cosine / Marker

Bidirectional

www.aerotech.com

Chapter 3

91

«
...
89
90
91
92
93
...
»

Содержание Ndrive HPe 100



















































































































Отзывы:

Нет отзывов

Похожие инструкции для Ndrive HPe 100

1.5 24 A Series

Бренд: Lenze Страницы: 70

FRENIC-Eco Series

Бренд: Fuji Electric Страницы: 112

Бренд: ZF-DUOPLAN Страницы: 37

Бренд: Saci Страницы: 40

VLT BACnet/IP MCA 125

Бренд: Danfoss Страницы: 18

Бренд: K&R Страницы: 362

Dual Hose Reel-Direct Drive K-32

Бренд: Hubbell Страницы: 4

SmartPilot X-10

Бренд: Raymarine Страницы: 12

Бренд: Sealey Страницы: 6

Бренд: Leadshine Страницы: 23

SUBDRIVE CONNECT PLUS

Бренд: Franklin Electric Страницы: 56

TECHNODRIVE MG 5020SC

Бренд: Twin Disc Страницы: 54

DVD+RW ATAPI Drive

Бренд: Iomega Страницы: 20

Бренд: ElectroCraft Страницы: 39

SERVOPACK Sigma 7S Series

Бренд: YASKAWA Страницы: 47

Бренд: Topcnc Страницы: 104

Бренд: D+H Страницы: 20

LDP-C 120-40 NG

Бренд: PICOLAS Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды