Aerotech Ndrive HPe 100 Скачать руководство пользователя страница 69

Страница: 69 / 114

Installation and Configuration

Ndrive HPe 50/75/100

2.8. FireWire Interface

The FireWire bus is the high-speed communications connection to the Ndrive HPe 50/75/100 operating at
400 megabits per second. All command and configuration information is sent via the FireWire port.

Table 2-41:

FireWire Card Part Numbers

Part Number

Description

NFIRE-PCI

OHCI compliant FireWire PCI interface card, 3 port

NFIRE-PCIE

OHCI compliant FireWire PCIe x1 interface card, 2 port

NFIRE-PCI-TI-LP

Low Profile, OHCI compliant, PCI

NFIRE-PCIE-GOF

FireWire PCIE X1 Glass Optical Fiber Board

Table 2-42:

FireWire Repeaters (for cables exceeding 4.5 m (15 ft) specification)

Part Number

Description

NFIRE-RPTR-1394A-1394A

Extender for copper cable lengths greater than 4.5 m (15 feet).

NFIRE-RPTR-1394A-GOF

Glass Optical Fiber FireWire Repeater, Qty. 1 (Fiber Cable not included)

Table 2-43:

FireWire Cables (copper and glass fiber)

Part Number

Description

NCONNECT-60

6 m (20 ft) long, 6 pin to 6 pin

NCONNECT-45

4.5 m (15 ft) long, 6 pin to 6 pin

NCONNECT-30

3 m (10 ft) long, 6 pin to 6 pin

NCONNECT-15

1.5 m (5 ft) long, 6 pin to 6 pin

NCONNECT-9

0.9 m (3 ft) long, 6 pin to 6 pin

NCONNECT-10000-GOF

10 m (32.8 ft), glass fiber optical cable

NCONNECT-15000-GOF

15 m (49.2 ft), glass fiber optical cable

NCONNECT-20000-GOF

20 m (65.6 ft), glass fiber optical cable

NCONNECT-30000-GOF

30 m (101.7 ft), glass fiber optical cable

www.aerotech.com

Chapter 2

Содержание Ndrive HPe 100



















































































































Результаты поиска

Содержание Ndrive HPe 100

Отзывы:

Похожие инструкции для Ndrive HPe 100

Бренды по названию

Популярные бренды

Aerotech Ndrive HPe 100, Руководство по оборудованию

Результаты поиска

Содержание Ndrive HPe 100

Отзывы:

Похожие инструкции для Ndrive HPe 100

Бренды по названию

Популярные бренды