Aerotech Ndrive FCL Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 52

Aerotech Ndrive FCL Скачать руководство пользователя страница 28

Installation and Configuration

Ndrive FCL Hardware Manual

2.5. Position Synchronized Output (PSO) (TB101)

The Ndrive FCL includes a Position Synchronized Output (PSO) feature.

The PSO can be programmed to generate an output synchronized to the feedback position and is typically
used to fire a laser or sequence an external device. Trigger signals may be derived from a feedback channel
or a software trigger. The position synchronized output pulse is generated using high-speed hardware,
allowing minimal latency between the trigger condition and the output.

An RS-422 line receiver or opto-isolator is recommended, especially when using long cable lengths in noisy
environments or when high frequency pulse transmission is required. It is best to locate the line receiver or
opto-isolator close to the receiving electronics.

Table 2-12:

PSO Specifications

Specification

Value

Maximum Input Tracking Rate

(1)

Single-Axis Tracking

16.6 MHz

Dual-Axis Tracking

15 MHz

Maximum Quadrature Encoder Output
Frequency

-MXH Feedback

30 MHz

Maximum PSO Output (Fire) Frequency

(2)

with Differential Output

5 MHz

with Single-Ended Output

12.5 MHz

Firing Latency

Single-Axis Tracking

80 nsec

Dual-Axis Tracking

110 nsec

1.

Signals in excess of this rate will cause a loss of PSO accuracy.

2.

The optocoupler that you use on the output might have an effect on this rate.

Table 2-13:

PSO Pins on the TB101 A Connector

Pin

Description

In/Out/Bi

1

PSO Output -

Output

2

PSO

Output

Table 2-14:

PSO Pins on the TB101 B Connector

Pin

Description

In/Out/Bi

1

PSO Output

Output

28

Chapter 2

www.aerotech.com

«
...
26
27
28
29
30
...
»

Содержание Ndrive FCL





















































Отзывы:

Нет отзывов