Aerotech Ensemble HLe Скачать руководство пользователя страница 76

Страница: 76 / 112

Chapter 3

www.aerotech.com

3.3. Analog Outputs (TB303)

The analog output is set to zero when power is first applied to the system or during a system reset.

Table 3-12:

Analog Output Specifications (TB102 B)

Specification

Value

Output Voltage

-10 V to +10 V

Output Current

5 mA

Resolution (bits)

16 bits

Resolution (volts)

305 µV

N O T E :

Analog Output 0 on TB303 is tied to Analog Output 0 on J205 (see

Section 2.5.6.

). TB303 lets

you connect to all of the analog outputs from one connector (do not connect to AOUT0 at both TB303 and
J205).

Table 3-13:

Analog Output Connector Pin Assignment (TB303)

Pin#

Description

In/Out/Bi

Analog Output 0

Output

Analog Output 1

Output

Analog Output 2

Output

Analog Output 3

Output

Table 3-14:

Mating Connector Part Numbers for the Analog Output Connector

Type

Aerotech P/N

Phoenix P/N

Wire Size: AWG [mm

]

4-Pin Terminal Block

ECK01293

1881341

20-28 [0.5- 0.080]

Figure 3-7:

Analog Output Connector (TB303)

Ensemble HLe

-IO Expansion Board

Содержание Ensemble HLe

















































































































Результаты поиска

Содержание Ensemble HLe

Отзывы:

Aerotech Ensemble HLe, Руководство по оборудованию, Страница: 76 / 112

Результаты поиска

Содержание Ensemble HLe

Отзывы: