manualshive.com logo in svg

Aerotech Ensemble HLe, Руководство по оборудованию, Страница: 64 / 112

Поделиться
Скачать
Aerotech Ensemble HLe Скачать руководство пользователя страница 64

64

Chapter 2

www.aerotech.com

2.6. Brake Power Supply Connector (TB202)

TB202 is the power supply connection to the onboard solid state brake control relay. The relay can be used
to automatically control a fail-safe brake on a vertical axis. It can also be used as a general purpose output.

The brake is typically wired directly to the Motor Feedback connector and the brake power supply is
connected to TB202 (shown in

Figure 2-35

). The brake may also be connected in series with the Brake

Power Supply and interlocked using Motor Feedback brake pins (

Figure 2-36

). A varistor must be connected

across the brake to minimize high voltage transients.

The brake output can be software configured; refer to the Ensemble Help file for more information (see topics
for the EnableBrakeControl parameter and the BRAKE command).

When TB202 is used to power the solid state brake control relay, the mechanical brake control relay present
on the I/O board should not be used.

N O T E :

The brake power supply must be externally fused.

The user must verify that the brake power requirements are within the specifications of the brake control
relay.

Table 2-39:

Relay Specifications

Solid State Relay Rating

Maximum Voltage

24 VDC

Maximum Current

2.5 Amps

Turn-On/Turn-Off Time

< 3.2 ms Turn-On (typical) / 0.1 ms Turn-Off (typical)

W A R N I N G : Do not exceed the maximum specifications.

Table 2-40:

Brake Output Connector Pinout (TB202)

Pin#

Description

In/Out/Bi

1

Brake Power Supply (+)

Input

2

Brake Power Supply (-)

Input

Table 2-41:

Mating Connector (TB202)

Description

Aerotech P/N

Phoenix P/N

Tightening

Torque (Nm)

Wire Size:

AWG [mm

2

]

2-Pin Terminal Block

ECK01250

1803578

0.22 - 0.25

0.14 - 1.5 [26-16]

Ensemble HLe

Installation and Configuration

Содержание Ensemble HLe

















































































































Отзывы:

Нет отзывов