Aerotech Ensemble HLe Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 112

background image

Installation and Configuration

Ensemble HLe

2.5.2. Position Synchronized Output (PSO)/Laser Firing (J205)

The PSO can be programmed to generate an output synchronized to the feedback position and is typically
used to fire a laser or sequence an external device. Trigger signals may be derived from a feedback channel
or a software trigger. The position synchronized output pulse is generated using high-speed hardware,
allowing minimal latency between the trigger condition and the output.

The PSO output is available on the dual-function AUX Marker/PSO signal lines. The auxiliary marker must
be configured as an output using the PSOOUTPUT CONTROL command. Refer to the Help File for more
information.

An opto-isolated output is available on the TB302 connector of the -IO option (see

for more

information).

An RS-422 line receiver or opto-isolator is recommended, especially when using long cable lengths in noisy
environments or when high frequency pulse transmission is required. It is best to locate the line receiver or
opto-isolator close to the receiving electronics.

Table 2-26:

PSO Specifications

Specification

Value

Maximum Input Tracking Rate

(1)

Single-Axis Tracking

16.6 MHz

Dual-Axis Tracking

8.33 MHz

Triple-Axis Tracking

8.33 MHz

Maximum Quadrature Encoder Output
Frequency

Standard Feedback

40 MHz

-MXH Feedback

25 MHz

Maximum PSO Output (Fire) Frequency

(2)

12.5 MHz

Firing Latency(3)

Single-Axis Tracking

160 nsec

Dual-Axis Tracking

220 nsec

Triple-Axis Tracking

220 nsec

1.

Signals in excess of this rate will cause a loss of PSO accuracy.

2.

The optocoupler that you use on the output might have an effect on this rate.

3.

MXH encoder multiplier options have an additional latency of ~3.25 microseconds between the measurement position and the

update of the PSO hardware.

N O T E :

When using the MRK± signals with single-ended systems,

do not

connect MRK+ or MRK- to

GROUND (GND).

Software controlled PSO pre-scalars may be used to limit the data rate of each encoder being tracked
without affecting the servo loop data rate.

Table 2-27:

PSO Output Pins on the Auxiliary I/O Connector (J205)

Pin#

Description

In/Out/Bi

19

Auxiliary Marker- / PSO output

Bidirectional

20

Auxiliary / PSO output

Bidirectional

23

Analog Common

-

www.aerotech.com

Chapter 2

55

«
...
53
54
55
56
57
...
»

Содержание Ensemble HLe

















































































































Отзывы:

Нет отзывов

Похожие инструкции для Ensemble HLe

Бренд: Gardena Страницы: 100

Бренд: IBM Страницы: 72

Бренд: UE Страницы: 4

Бренд: XBOX Страницы: 7

Бренд: BEIER-Electronic Страницы: 22

CITY ELITE SINGLE

Бренд: Baby Jogger Страницы: 3

Бренд: Samson Страницы: 56

Бренд: Hach Страницы: 128

Бренд: Yamato Страницы: 33

Бренд: Eaton Страницы: 288

Бренд: Farfisa Страницы: 20

Бренд: Racal Instruments Страницы: 64

ESD-5550 Series

Бренд: GAC Страницы: 12

Бренд: Parker Страницы: 30

Compax3M Series

Бренд: Parker Страницы: 52

Бренд: Parker Страницы: 337

Бренд: Xilinx Страницы: 2

Бренд: Measurement Computing Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды